Discovering Plumbing Basics is Important For Installing a Bathtub
Discovering Plumbing Basics is Important For Installing a Bathtub
Blog Article
Everyone has got their unique opinion on the subject of How to Install a Bathtub.
Setting up a tub isn't specifically rocket science, yet it does need strong plumbing, woodworking, and also often, tiling skills. Changing an old bathtub with a new one is likewise a moderately challenging project. If the old tub is easily available, the job can move immediately; if you have to open up a wall to get rid of the old bathtub and also position the brand-new bath tub, the task is a lot harder. In either situation, the task is within a home handyman's skills, although you will require a helper to vacate the old bathtub and also set in the brand-new one. Make certain you have certified yourself for the work and fit trying it. As opposed to working with a service provider to take over a halfway-completed job, it is much better to think about using one before you start. Possibilities are you might need an expert plumber to make tube connections.
This short article will assist you mount a new tub in your restroom if you have currently bought a new bathtub and also don't need to alter the plan of your previous water pipelines.
Your tools and material list must make up the following:
Getting ready for the Installment
To start with, the supporting frame provided with the bath should be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the faucet includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets device to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, then the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be fairly bothersome due to the limited accessibility that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a towel all set for the staying water that will certainly come from the pipelines. Once the supply pipes have been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning during this process. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleaned of any type of old securing substance.
Prior to carrying on to fit the brand-new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, position the tub in the required placement. The wooden boards are helpful in evenly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and also adjusting the feet on the tub up until the level reads level.
To install faucets, fit the bottom of the outermost flexible tap connector to the appropriate supply pipeline by making a compression join; after that do the very same for the other tap.
Turn on the water supply and also check all joints and also brand-new pipework for leaks and also tighten them if essential. Fill up the bathtub as well as likewise examine the overflow outlet and the typical outlet for leakages.
Finally, deal with the bath paneling as defined in the manufacturer's user's manual. Tiling and securing around the bath tub ought to wait till the tub has been used a minimum of when as this will resolve it into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in place in between the tap and also the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in position, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The previous kind must be linked to the tap ends first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bath meets the tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall between the bathroom as well as the tiling, causing problems with moisture and also feasible leaks to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and fittings. They are sold in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill up the bath tub with water prior to sealing, to enable the activity experienced when the bathtub is in use. The sealant can crack fairly early if you do not take into account this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently available on the marketplace. It is recommended to fit the tiles using waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that piece of content was beneficial. Be sure to set aside a second to distribute this content if you appreciated it. We value reading our article about How to Install a Bathtub.
Schedule A Free Estimate Report this page